Kreg KMS7102 Table Saw Precision Miter Gauge System

Kreg KMS7102 Table Saw Precision Miter Gauge System Review

See more picture

Kreg KMS7102 Table Saw Precision Miter Gauge System Feature

• Factory Calibration. Guaranteed out of the box to .003 accuracy of 6-inches
• Gauge head is CNC machine perfectly square to the bar and table ( no stampings)
• Vernier scale allows fast, 1/10th-degree angle adjustments
• Microadjuster allows additional angle adjustment to 1/100th degree
• Postive stops at 0, 10, 22-1/2, 30 and 45-degrees; limited lifetime warranty

We’ve found that even on high-end saws, the miter gauge is sometimes not the best it could be – a situation easily resolved by the folks at Kreg. You probably know them for their ingenious pocket hole system, but this miter gauge is worthy of fame in its own right.

It’s not like any we’ve seen before, with a handful of features that work together to give you the ability to set an angle cut accurately to 1/10th of a degree – and beyond that, to adjust to 1/100th of a degree (hats off to you if you’re that precise!)

Setup takes a little bit of time and patience, but the results are well worth it. It’s got a super accurate length scale with a magnifying lens cursor, similar to those on good table saws, and the curved flip stop can be used with the fence as is, or you and a pair of pliers can modify it easily for permanent use with a sacrificial fence. This clever curved design lets you slide your stock right under it. The slot bar has five patented nylon screws along its length that let you custom fit it to your table saw slot, completely eliminating any play.

It’s got the positive stops you expect, at 0, 22.5, 30 and 45 degrees, and they’re marked by preset holes that accept a tapered brass pin, which locks in the angle with absolute precision. The gauge is marked with diamonds every five degrees for great legibility, too. But what sets this gauge apart from the pack is its Vernier scale, allowing you to set any angle in tenth-of-a-degree increments. Unless you have a degree in mathematics, don’t try to understand the process – it’s confusing and non-intuitive. Instead, just follow the step-by-step directions, and you’ll get absolute accuracy every time.

And when Kreg calls something a "micro-adjustment" mechanism, they really mean micro. With this miter gauge, you can actually increase your angle by 1/100th of a degree by turning a nylon screw that increases the space between the fence and the gauge. For each .001 inch you put between the fence and gauge, you increase your angle by 1/100th of a degree.

Kreg’s really hit the accuracy bullseye with this miter gauge, and adding it to even a so-so saw will give you fantastic results. Take your time with setup and follow the directions for the Vernier scale, and you’ll be as taken with it as we are. -- Kris Jensen-Van Heste Cut perfect miters consistently with Kregs Precision Miter Gauge System. A number of unique features makes this one of the most precise miter gauges on the market today. Factory calibrated accuracy starts with a gauge head that is machined on a computerized milling machine for absolute precision.

Check price now

Related Products

• Kreg PRS3020 True-FLEX Featherboard - Twin Pack
• Kreg KMS7215 Micro-Adjuster for Band Saw and Router Table Fences
• Kreg PRS3090 3" Dual Locking Caster-Set (4 Piece)
• Kreg PRS1040 Precision Router Table System
• Kreg PRS3400 Precision Router Table Set Up Bars, Set of 7

Customer Reviews

Jan 31, 2012 14:01:06

Bench Dog 40-001 ProTop Contractor Benchtop Router Table

Bench Dog 40-001 ProTop Contractor Benchtop Router Table Review

See more picture

Bench Dog 40-001 ProTop Contractor Benchtop Router Table Feature

• Ample 16-by-22-inch router table with plastic laminate top
• Clear acrylic insert accepts most routers; melamine cabinet
• Extruded aluminum fence with T-slots
• All necessary hardware and assembly instructions included
• Limited 2-year warranty

Don't let its compact size fool you. The award-winning Bench Dog 40-001 ProTop Contractor Benchtop Router Table makes use of a unique forward offset router location and the dual-position ProFence to provide as much usable work surface as most full-size router tables. Designed to be durable, easy to move around the job site, and ready to accept any router, it provides the versatility, stability, and guidance you need to complete precision projects safely.

The ProTop Contractor Benchtop Table adds versatility and precision to your router setup. View larger.

Versatile Design for Precision Work
Whether you're a professional craftsperson or a serious do-it-yourselfer, a router table like the ProTop Contractor lets you tackle jobs that would be difficult or impossible to complete precisely with a handheld router.

A top-quality fence is critical to the performance of any router table system, and this system relies on the feature-loaded ProFence. Its heavy-duty, one-piece aluminum frame is fully machined on the front and bottom surfaces to ensure it's flat, true, and square. Easy-adjust sub-fences and bit guard are also included.

The ProTop Contractor provides a flexible setup that can be adjusted to project-specific needs, with an aluminum miter accessory track that is adjustable to fit all standard miter gauges, plus accessory T-slots on both the table and fence that are perfect for mounting featherboards, stops, fence risers, and switches. This allows you to accommodate the full range of router applications, from cutting dadoes and slots to crafting precise joints. For work with large panels, this table also offers dual fence slots, so you can flip the fence around quickly and easily.

An integrated 2-1/2-inch dust port fits standard shop vac hoses to help keep your work area clear of debris for safety, visibility, and operator comfort.

Dependable Construction for Tough Jobs
The non-marring laminate top is built using stress-skin construction for strength and flatness, and it measures 24 x 16 inches to provide a large work area. Exclusive twin steel rails support your router, while the enclosed birch plywood cabinet reduces dust and noise, and its solid panel construction makes it stronger than cheap plastic or stamped steel stands. The cabinet's rubber feet prevent table slippage and double as isolation mounts for dramatically reduced vibration.

This table's setup will accept any router, and the included router plate is predrilled to make installation extra-easy for most popular routers from leading brands like Craftsman, DeWalt, Fein, Hitachi, Makita, Ryobi, and Skil. The 15-inch inside-cabinet height provides plenty of space for whatever router you use, plus room for Bench Dog's ProLift and other accessories (not included).

This portable router table weighs just 40 pounds, and it requires assembly. It is backed by a limited lifetime warranty.

About Bench Dog
Bench Dog offers a growing line of router tables, safety accessories, and tools for everyone from building and woodworking professionals to schools and serious beginners.

The company began in 1995 with Norston Fontaine, Karen Slatter, and the simple idea that great tools are the result of great design and solid engineering. Since then, Bench Dog tools have received an enthusiastic response from customers, trade publications, and the woodworking community at large.

What's in the Box
Table top, fence, dust port, bit guard, miter track, pre-drilled router insert plate, mounting screws, and cabinet.
Includes ProTop Contractor Router Table - 40-001

Check price now

Related Products

• MLCS 8377 15-Piece Router Bit Set with Carbide-Tipped 1/2-Inch Shanks
• Bosch 1617EVSPK 12 Amp 2-1/4-Horsepower Plunge and Fixed Base Variable Speed Router Kit with 1/4-Inch and 1/2-Inch Collets
• Bench Dog 10-035 Bench Cookie Work Grippers, 4-Pack
• Bench Dog 40-011 Feather-Loc Double Featherboard for Table Saws & Router Tables
• Bench Dog 10-012 Miter Slot Adapter

Customer Reviews

Jan 29, 2012 06:39:04

DELTA 78-958 50-Inch-52-Inch Table Saw Mounted Blade Guard for 12-Inch - 14-Inch Blades

DELTA 78-958 50-Inch-52-Inch Table Saw Mounted Blade Guard for 12-Inch - 14-Inch Blades Review

See more picture

DELTA 78-958 50-Inch-52-Inch Table Saw Mounted Blade Guard for 12-Inch - 14-Inch Blades Feature

• For 12-inch or 14-inch table saws
• Designed for use with 12 to 14-inch saw blades with 50-52 inch rip capacity
• Features T-Square and anti-kickback spreaders
• Works with 50-inch fence systems

The DELTA 78-958 Table Saw Mounted Blade Guard is designed for saws with a 12- to 14-inch blade and 50- to 52-inch rip capacity. It features T-Square and anti-kickback spreaders and is designed for commercial 50-inch fence systems

Check price now

Related Products

Customer Reviews

Jan 27, 2012 14:38:06

Proxxon 38070 FKS/E Table Saw

Proxxon 38070 FKS/E Table Saw Review

See more picture

Proxxon 38070 FKS/E Table Saw Feature

• Unit includes vacuum cleaner adapter
• 110-115V, 60HZ; weight 11.5 lbs.
• Replacement blades available 28731 crosscut, 28732 36 tooth carbide, 28734 24 tooth carbide, 28735 diamond coated blade, 28736 dado head set

Accurate, straight cuts. Standard with height adjustment and tilting blade. The ideal machine for straight, miter and compound cuts. Useable on all wood types, non-ferrous metals, plastics, as well as rubber, cork, etc. Even the smallest items may be cut cleanly, eliminating subsequent finishing. A table indicates the recommended speeds for various materials. Substantial construction with load bearing parts made of die-cast aluminum. The machined aluminum work table measures 11 39/64" x 9 29/64". A miter slot and fence are provided. An extension wing is housed integrally and pulled out to create an even more effective table width up to 19 11/16" . The drive of the unit is accomplished via a special, quiet motor and Optibelt toothed belt. The blade arbor has ball bearings and is fitted with a TCT blade, size 3 5/32" x 1/16" x 13/32", 24 teeth available as accessory NO 28 734 as standard. For other saw blades for various materials, please have a look at our selection of saw blades for this machine below. The machine may be used with all blades providing Ø 2" to 3 11/32" with 13/32" bore. The depth of cut is adjustable from 3/64" - 7/8" and the blade may be tilted through 45°. Technical data: Speeds electronically variable from 4,400 to 6,800 rpm Cut Depth 3/64" to 7/8" Table Size 11 39/64" x 9 29/64" Overall Size 11 13/16" x 10 5/16" x 6 43/64" w/o extension wing Volts 110-120V AC, 60 Hz Weight 11.5 lb. Note: For even smaller projects consider also our smaller circular saw KS 115. Available accessories: A circular saw can only be efficient, if the used saw blade is appropriate. See below our selection of high quality saw blades for many different applications and materials. We only offer industrial quality with a high lifetime: Super cut NO 28 731 Tungsten carbide tipped NO 28 733 Tungsten carbide tipped NO 28 734 Diamond coated NO 28 735 Dado head set NO 28 736.

Check price now

Related Products

• Proxxon 28731 85mm Crosscut Saw Blade Super Cut for FKS/E 80-Teeth
• Proxxon 28732 3-9/64-Inch 80mm Carbide Tipped Saw Blade 36-Teeth
• Proxxon 28736 Dado Head Set
• Proxxon 37160 KGS 80 MICRO Chop Saw
• Proxxon 37050 Micro Shaper MT 300

Customer Reviews

Jan 26, 2012 08:04:04

Powermatic 1792000K Model PM 2000 3 Horsepower Cabinet Saw with 50-Inch Accu-Fence, 2 Cast Iron Extension Wings, Table Board, and Legs, 230-Volt 1 Phase

Powermatic 1792000K Model PM 2000 3 Horsepower Cabinet Saw with 50-Inch Accu-Fence, 2 Cast Iron Extension Wings, Table Board, and Legs, 230-Volt 1 Phase Review

See more picture

Powermatic 1792000K Model PM 2000 3 Horsepower Cabinet Saw with 50-Inch Accu-Fence, 2 Cast Iron Extension Wings, Table Board, and Legs, 230-Volt 1 Phase Feature

• Left-tilting table saw with 50-inch fence; arbor lock; built-in retractable casters; dust collection
• 3-horsepower, 1-ph, 230-volt motor; riving knife with quick release; poly-v belt
• Cast-iron trunnion and extension wings
• Includes saw, fence, left and right wings, arbor wrench, (no blade or power cord)
• 85-by-37-by-34-1/2-inches; 600-pounds; 1-year warranty

Powered by a three-horsepower, one-Ph motor, the award winning Powermatic PM2000 10-Inch Cabinet Saw sets a new standard for innovation with an array of patented features and massive body design. It boasts the heaviest cast-iron base in its class to virtually eliminate table vibration, oversized cast-iron tables, and a push-button arbor lock that's conveniently accessible from above the tabletop.

The PM2000 10-Inch Cabinet Saw At a Glance: Poly-V drive belt system delivers efficient, quiet operation Push-button arbor lock (patent pending) for rapid blade change Wide-stance heavy-duty trunnion for stability and smooth blade positioning Built-in retractable caster system for immediate shop mobility Industrial-duty 50-inch Accu-Fence system ensures accurate cuts

The cast-iron base features a built-in, retractable, 4-wheel caster system. View larger.

Oversized, cast-iron hand wheels for quick blade adjustment. View larger.

The push-button arbor lock allows for rapid blade changes. View larger.

The built-in dust collection system ensures long motor life. View larger.

Rugged Design for Smooth Operation
Designed with input from professional woodworkers, the PM2000 provides incredible quality, efficient functionality, and long-term durability.

Its refined heavy-duty trunnion mechanism features rigid, box-style cast-iron construction, high-end bearings, and a conical-shaped worm gear drive with an increased contact area to enhance the smooth, solid feel of the tilt and height adjustment.

A pair of oversized, eight-inch-diameter cast-iron hand wheels, each with a large spinner handle, makes blade height and bevel adjustments virtually effortless. And to prevent long-term use from loosening the hand wheels on their shafts, they are locked in place with machined grooves and keys rather than setscrews.

Precision Machined Arbor and Poly-V Drive Belt System
The full-length 5/8-inch diameter arbor is precision machined from stress-proof steel to exceptionally high tolerances for accuracy. It accepts stacked dado sets up to 13/16-inch wide, and because there is no gap between the threads and arbor shank, thin chippers won't hang out of line.

Also, the push-button arbor lock makes for rapid blade changes, while a high quality poly-V drive belt system transmits more power without slippage or excessive noise.

Generously Sized Tables and Extensions
All the high-luster, cast-iron surfaces are finely ground to ensure a smooth, mar-free work surface that provides more support for big jobs and have both a front- and rear-edge bevel for hassle-free work piece positioning.

Measuring approximately 30.5 x 22.0 inches (W x L), the primary cast-iron tabletop expands to 42 inches long when the standard cast-iron extension wings are bolted up, giving you plenty of space for even large work pieces.

Safe, Sturdy Design
The PM2000 also comes equipped with a newly designed magnetic On/Off switch for safety. To prevent accidental start-ups, there's a removable magnetic "key" that disables the switch when it's not in place. For additional protection against damage, a quick-release riving knife greatly reduces binding/kickback risk.

High-Tech Guard System
The PM2000's blade guard and riving knife system can be adjusted tool-free for the job at hand. At the same time, because the riving knife is mounted directly to the blade mechanism, the gap between it and the blade never changes during height or angle adjustments.

This maintains the safety a riving knife affords in virtually all cutting situations.

Get Accuracy and Precision
An industrial-duty 50-inch Accu-Fence System ensures accurate cuts. Adjustable angle indicators on the blade bevel scale for repeatable bevel cuts. Additionally, a heavy-duty, deluxe, micro-adjust miter gauge with a 13-inch extension fence ensures stable workpiece support and easy fine-angle adjustments.

Finally, to facilitate movement in and around the shop, the massive cast-iron base has a built-in retractable, four-wheel caster system.

Dimensions and Warranty Information
The PM2000 measures 37 x 39 x 85 inches (W x H x D), weighs 675 pounds, and is backed by a five-year warranty.

What's in the Box
One table saw; one table insert; one miter gauge assembly; one blade guard assembly; one switch in box; one push stick; one arbor wrench; two lock knobs; two swivel handles; one riving knife and pawl assembly; one hardware bag; two extension tables packed in individual boxes; two hinge pins; one side cover; manual; and warranty card.
Includes PM2000 3 HP 10-in Single Phase Left Tilt Table Saw With 50-in Accu-Fence - 1792000K, 50-in Accu-Fence® System, 10-in Standard Left and Right Cast-Iron Extension Wings, Arbor Wrench, Motor Cover, (Blade and Power Cord Not Included)

Check price now

Related Products

• Forrest WW10407125 Woodworker II 10-Inch 40 Tooth ATB .125 Kerf Saw Blade with 5/8-Inch Arbor
• Powermatic 1791788 PM2000 Table Saw Dado Insert
• Powermatic 1791786 PM2000 Table Saw Zero Clearance Insert
• Powermatic 1791787 Low Profile Riving Knife
• Powermatic 54A Deluxe 6-Inch Jointer with Quick-Set Knives

Customer Reviews

Jan 24, 2012 13:51:04

Freud D1080X Diablo 10-Inch 80-tooth ATB Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating

Freud D1080X Diablo 10-Inch 80-tooth ATB Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating Review

See more picture

Freud D1080X Diablo 10-Inch 80-tooth ATB Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating Feature

• 10-inch 80T ultra fine finish cut-off blade with a laser-cut 5/8-inch arbor
• Laser cut stabilizer vents trap noise and vibration keeping it cool and reducing blade warp
• Heat expansion slots let blade expand due to heat build-up; durable micrograin titanium carbide
• Tri-metal shock resistant brazing allows carbide tips to withstand extreme impact for maximum durability
• Laser cut arbor for accurate blade rotation reducing vibration and premature wear

For a blade dedicated to cutting ultra-fine finish work with remarkably clean, chip-free results, look no further than the Freud D1080X Diablo 10-Inch Ultra-Fine-Finish Saw Blade. Ideal for fine cabinetmaking, this is your go-to blade for slicing through oak, pine, melamine, veneer plywood, and delicate molding. For strong, long-lasting resistance, the blades feature a tough steel plate and high-density carbide tips.

Model # D1080X Diameter 10" Machine Use Miter/Slide Miter Saw, Table Saw Application Finishing Teeth 80 Hi-ATB Arbor 5/8" Kerf .098" Hook Angle 15°

Makes Clean, Chip-Free Cuts in Delicate Finish Work
Achieving premium results when creating finish crosscuts in ultra-fine materials is all about clean, accurate cuts. The Freud D1080X makes this process easy, fast, and precise. To save you time, most cuts made by this blade require little to no sanding.

Trim carpenters, fine cabinetmakers, and avid do-it-yourselfers will want to keep this blade on hand for those special jobs that call for making ultra-fine finish crosscuts in delicate pieces. Appropriate application materials include oak, pine, melamine, veneer plywood, and delicate molding.

Produces Smooth, Quiet Cuts with Laser-Cut Kerf
The Freud D1080X's clean-cutting design means that you can enjoy the comfort of smooth performance. The thin 0.98-inch kerf between the blade's 80 Hi-ATB (alternate-top bevel) teeth is laser cut to provide ease of feed, so you have more control over the blade's position. This helps maximize both the accuracy of the cut and the efficiency of your work, so you enjoy a job well done and the ability to complete more tasks in less time.

An added bonus, the blade's laser-cut stabilizer vents reduce noise and vibration during operation, keeping your work environment more relaxed and your hands more in control. This feature also reduces friction and warping, helping to extend the blade's cutting life.

Features Shock-Resistant Carbide for Long-Lasting Precision
So you can count on it over the long term, the Freud D1080X is designed for durability. The blade's hardy teeth are protected by Freud's exclusive shock-resistant TiCo Hi-Density Carbide formula, which helps fight wear and tear and maintains blade sharpness up to four times longer than standard carbide. And protecting the blade is Perma-Shield Non-Stick Coating that provides resistance to heat and corrosion.

Fits Miter and Table Saws
The Freud D1080X is a great addition to your workshop because it's designed with the versatility to fit a variety of table and miter saws, including sliding miter saws.

This product is covered by Freud's Limited Lifetime Warranty.

What's in the Box
Freud D1080X Diablo 10-Inch Ultra-Fine-Finish Saw Blade.
FREUD SAW BLADE *10" *80T *5/8" arbor *Ultra finish cut *Super thin laser cut kerf *"Red" Perma-Shield coated *Laser cut stabilizer vents *Laser cut heat expansion slots

Check price now

Related Products

• Freud D1050X Diablo 10-Inch 50-tooth ATB Combination Saw Blade with 5/8-Inch Arbor and PermaShield Coating
• Freud D0760X Diablo Ultra Finish Saw Blade ATB 7-1/4-Inch by 60t 5/8-Inch Arbor
• Freud LU87R010 10-Inch 24-Tooth FTG Thin Kerf Ripping Saw Blade with 5/8-Inch Arbor and PermaShield Coating
• Bosch TS1003 Table Saw Left Side Support Extension
• DEWALT DW713 10-Inch Compound Miter Saw

Customer Reviews

Jan 22, 2012 23:58:05

Makita 2705X1 10-Inch Contractor Table Saw with Stand

Makita 2705X1 10-Inch Contractor Table Saw with Stand Review

See more picture

Makita 2705X1 10-Inch Contractor Table Saw with Stand Feature

• Tool-less modular blade guard system with an adjustable riving knife
• Two on board independent stowable anti-kickback pawls and riving knife/spreader for through cuts
• T-slot miter gauge grooves accepts commercial accessories with T formed shanks for versatile cutting
• Rips 4X material in one pass
• 1 year warranty

Makita's 10-Inch Contractor Table Saw with Portable Stand is a versatile and powerful table saw for use in the shop or on the jobsite. The 2705X1 combines a range of convenience and ease-of-use features with large capacity and 15 AMP power, making it a true best-in-class table saw for a range of professional applications. The portable stand is jobsite tough for easy transport.

View larger

2705X1 Features VERSATILE - Adjustable dual slide guards allow for ease of measurements from the blade to the rip fence for cutting set ups EFFICIENT - Riving knife/spreader adjust to 3 different positions for through, non-through and dado cuts PRECISION - Precision machined table top remains flat and true for accurate cuts PERFORMANCE - Right extension table allows for greater cutting capacity with the capability to rip 4x8 sheets of plywood INCLUDES - Carbide tipped blade, rip fence, miter gauge, wrenches and stand

Tool Specifications Blade Diameter 10" Arbor 5/8" Max. Cutting Capacity at 90° 3-5/8" Max. Cutting Capacity at 45° 2-1/2" No Load Speed 4,800 RPM AMPS 15.0 Table size (W x L) 24-5/8" x 22-1/4" Net Weight 114.7 lbs. (with stand)

15 AMP Power with New "Tool-Less" Blade Guard System
The 2705X1 is powered by a 15 AMP motor that delivers 4,800 RPM with an electric brake for maximum productivity. The large cutting capacity (3-5/8 inches at 90° and 2-1/2 inches at 45°) can rip 4X material in one pass, and can use up to a 13/16-inch dado blade. The 2705X1 also features a tool-less modular blade guard system with adjustable dual side guards to allow for ease of measurement from the blade to the rip fence for cutting setups. The two on-board independent stowable anti-kickback pawls and riving knife/spreader allows for through cuts. In addition, the riving knife/spreader adjusts to three different positions for through, non-through and dado cuts - and it adjusts without removing the throat plate.

More Capacity and More Accuracy
The precision-machined table top remains flat and true for accurate cuts, right out of the box. The right extension table allows for greater cutting capacity with the capability to rip 4'x8' sheets of plywood. Precision adjustment features include a 3/8x3/4-inch T-slot miter gauge with grooves that securely support cutting material for wide crosscutting jobs. The rip fence slides effortlessly across the flat table top for more precise adjustments. Convenience features include a large on and off switch, and easy to read scale for fast adjustments. The saw has complete storage capacity to hold most commonly used accessories including saw blade, power supply cord, miter gauge, rip fence, push stick, wrench, safety guard and dado blade.

Durable and Portable Stand
The 2705X1 includes a durable and portable stand with heavy-duty wheels and powder coated finish for extended durability. The spring loaded system is easy to adjust and fold for storage.

Versatile Design for a Range of Applications
The 2705X1 is a versatile and powerful table saw for use in the shop or on the job site. The 2705X1 is engineered for remodelers, furniture makers, finish carpenters, cabinet installers, decking and flooring contractors, and general contractors seeking a best-in-class 10-inch contractor table saw for the jobsite or on the benchtop. The 2705X1 is just another example of Makita's commitment to innovative technology and best-in-class engineering.

About Makita's Table Saws
Makita's table saws deliver shop-quality cuts to the jobsite. The large capacity will rip 4X material in one pass, while the precision-machined table top remains flat and true for accurate cuts, right out of the box. Precision features include a new modular blade guard system with adjustable dual side guards to allow for ease of measurement from the blade to the rip fence for cutting setups. A durable and portable table saw stand is also available. This versatile table saw is ideal for use at the jobsite or in the shop.

About Makita
Makita is a worldwide manufacturer of industrial quality power tools and offers a wide range of industrial accessories. Makita applies leading-edge innovation to engineer power tools that are more compact and energy efficient, yet deliver industrial strength power and results. Makita U.S.A., Inc. is located in La Mirada, California, and operates an extensive distribution network located throughout the U.S. For more information, please call 800/4-MAKITA (800/462-5482) or visit makitatools.com. Makita is Best in Class Engineering.

Warranty
Every Makita tool is thoroughly inspected and tested before leaving the factory. If you are not satisfied with any Makita tool within 30 days of purchase, return it and Makita will provide a replacement or refund. Each Makita tool is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. Please see makitatools.com for complete details.

What's in the Box
Makita 2705X1 10-Inch Contractor Table Saw includes: 32T Carbide tipped blade, Rip fence, Miter gauge, Wrenches, and Portable table saw stand.
Makita 2705X1 10" Contractor Table Saw With Stand Makita 2705X1 10" Contractor Table Saw With Stand Features: Powerful 15.0 AMP motor delivers 4,800 RPM "Tool-less" modular blade guard system with an adjustable riving knife/spreader Blade guard assembly with cam lock provides easy "tool-less" installation or removal Adjustable dual side guards allow for ease of measurement from the blade to the rip fence for cutting set-ups

Check price now

Related Products

• Makita LS1216LX 12-Inch Dual Slide Compound Miter Saw with Laser and Stand
• Makita LS1016LX 10-Inch Dual Slide Compound Miter Saw with Laser and Stand
• MLCS 8377 15-Piece Router Bit Set with Carbide-Tipped 1/2-Inch Shanks
• Makita LS1216L 12-Inch Dual Slide Compound Miter Saw
• Makita Bare-Tool BJV180Z 18-Volt LXT Lithium-Ion Cordless Jig Saw

Customer Reviews

Jan 21, 2012 19:09:14